Weaving of roses from beads

Rose from beads - simple weaving technique

Weaving of roses from beads

The rose from beads consists of 5-6 large petals, the same number of small and middle (petal, rolled up by a tube). Under the flower is a calyx of green color and five long sepals.

First weave the middle - the middle petal, folded tubule

1. 
   The middle petal is woven from a light pink bead, using the technique of parallel weaving.


2. 
   The petal pattern is as follows: 13 (3 times) - 12 (3 times) - 11 (2 times). For such a petal, you will need 70 cm of wire.


3. 
   After making the workpiece of the middle, pass one of the ends of the wire through all the beads of the middle row - both ends of the wire should be on the same side of the weave.


4. 
   Finish the petal in a tube in the direction from the first row to the last.


5. 
   Between the rows, weave the wire to fix the folded petal, and twist the ends of the wire several times.

Then weave a small petal

1. 
   A small petal, follow the first scheme of light and dark pink beads on a wire 70 cm long.


2. 
   A small petal should be done in the same technique as the middle of the flower.


3. 
   Make 5 of these petals.

Weaving of a large petal

1. 
   A large petal is also pulled from a light and dark pink beads, but according to another scheme.


2. 
   A large petal make of two parts, each of which is padded on a separate piece of wire about 90-100 cm long.


3. 
   The first three rows of dark pink beads do on one of the wires, then put the second wire, bent in the form of a hairpin, in the middle of the third row.


4. 
   The ends of the wire are twisted 2-3 times


5. 
   Then weave the parts of the petal separately with the scheme: first one part, then the second


6. 
   Pin the parts of the petal to each other, as each row of the second part of the large lobe runs.


7. 
   Make 6 large petals.

Weaving of sepals and calyx

1. 
   The sepal is made from green beads in the technique of parallel weaving on a piece of wire 55 cm long.


2. 
   The scheme of weaving of sepals: 1 (5 times) - 2 - 3 - 4 - 5 (3 times) - 4 - 3 - 2 - 2.


3. 
   The cup is made of green beads in the same technique.


4. 
   The scheme of weaving a cup: 9 rows of 7 beads per 60 cm of wire.


5. 
   Weaving the last row, one of the ends of the wire pass through the first row, so that the ends of the wire are on one side.


6. 
   Twist the ends of the wire several times.


7. 
   Sepals make 5 pieces.

Weaving of leaves for roses

1. 
   The sheet, like a large petal, is woven from two halves on two wires (length - 55 cm).


2. 
   First, weave one part of the sheet in the parallel weaving technique.


3. 
   The scheme for weaving the sheet is as follows: 1 - 2 - 3 - 4 - 5 - 6 (2 times) - 7 (2 times) - 6 (2 times) - 5 - 4 - 3 - 2 - 1.


4. 
   The second part is connected with the first in the process of weaving after each row.


5. 
   Make 10 such leaves from beads.

Bouquet of rose buds

1. 
   For bud, weave a dark pink petal according to the middle petal and five sepals.


2. 
   The scheme for weaving bud: 1 (5 times) - 2 - 3 - 4 - 5 (3 times) - 4 - 3 - 2).


3. 
   Seagulls weave among themselves in the process of weaving, immediately after the fulfillment of each rad.


4. 
   Begin to weave from the second row of 5 beads.

Assembling a rose from beads

The weaving of the rose from the beads is over, we begin to collect it.

1. 
   Take the middle petal, to it, consistently attach 5 small and 6 large petals (they should be evenly distributed around the middle lobe).


2. 
   Under the lower petals place 5 sepals and for 1 cm twist the wire.


3. 
   Insert the flower leg into the cup and twist the wire under it for 6-7 cm.


4. 
   Petal bud insert into the center of the woven sepals.


5. 
   Prostvochki under sepals divide into pairs and on each of them type on 5 beads of green color.


6. 
   Under the resulting small cup, twist the wire by 7-9 cm.


7. 
   Then collect two twigs, each of 5 leaves


8. 
   Under the lower leaves twist the petioles from the wire - 3 cm for one branch, and 5 for the other.


9. 
   The first branch with a stem of 3 cm attach to the flower's stem at a distance of 6 cm and twist the wire by 3-5 cm.


10. 
    Attach the bud and one more twig, twist the wire to the end.


11. 
    The resulting stem of the flower is coated with PVA glue and tightly wrap the threads of a green mulina.