New Year's toys with their own hands

So it's time to decorate the New Year tree. But getting out Christmas toys from a secluded place, you suddenly find that they have become few, very few. What to do? You can go to the store and buy new toys, but high-quality New Year toys are expensive, and somehow do not want to buy substandard. There is an exit. Try to make New Year toys with your own hands. We are sure you will succeed!

Here are some examples of New Year's toys, which are easy to make by themselves.

New Year's toy "Openwork ball"

To make such a toy, take the airBall and blow to the necessary size of the future toy. Next, take a thread of your favorite color (better brighter) and, passing it into the needle, pierce the tube with glue (PVA) and stretch the thread through it. The needle should be laid aside, and the thread, moistened with plenty of glue, start wrapping your balloon. Winding should be in a chaotic order and the more - the better. When the whole ball is wrapped, cut the thread and leave the ball to dry. When the glue dries well, release air from the balloon and gently remove the ball. If, when blowing the ball, the threads are stuck to it, then, without pulling out the ball, inflate and blow it off several times. This will fix the shape of the toy.

New Year's toy "Bell"

To make this toy you will needa small plastic flowerpot, a rope, a large bead. In the bottom of the flower pot, pierce the hole, for example, with a hot nail. Decorate the pot with applique, colorful drawings, sparkles. Next, take a small piece of rope and tie one of its end with a knot. Put a large bead on the rope. Tie another rope on the rope, a little more than the height of the pot from the first knot. Pass the end of the rope into the opening of the flower pot from the inside, and then tie another knot.

Congratulations, a great New Year's toy "Bell" for the contest is ready. If desired, you can decorate your bell on top of the second bead and make a loop for hanging the toy on the Christmas tree.

New Year's toy "With hoarfrost"

To get the frosty effect on New Year's toysthere is one old proven method. It is necessary to take hot water in which to dissolve a lot of ordinary table salt. The solution must be very strong. In this solution, lower the toys and leave them for several hours or at night "to sour". After the toy, remove and dry without wiping. On dried toys, crystals of salt will precipitate - "hoarfrost" is ready!

New Year's toy "Ball"

This toy is made of cardboard. You will need three pieces of cardboard in different colors. Cut three identical circles. In the center of one circle, make a cross-cut. This will be a circle A. Cut the second circle in small cuts from above and below, in the center of the circle make a horizontal incision. This is circle B. The third circle is cut from above, from below and on the sides, in a direction from a line of a circle to the center. This is the circle B.

Now circle B needs to be folded in half and put it throughin the circle B. In circle A it is necessary to bend the corners of the incisions so that a square hole is obtained. Fold the circles B and B in half and thread them into the hole of the circle A. Undo the circles and corners of the notches. It remains only to attach a thread and your ball is ready!

New Year's toy "Garland"

To make this toy, cut a lotsmall rectangles of paper. The more rectangles there are, the longer the garland will turn out. Fold each rectangle in half and draw a link profile of the future chain. For example, draw a "half" of the number 8. Cut out the shape of the paper from the drawn outline. Now you can start compiling the chain. Spread one figure - it will be the starting link. Put the following figure in the "ear" of the link and fold it in half in the folding position. Also pass the next figure, and the next - until you run out of paper! You can make a garland colorful. Then alternate the colored links in a certain sequence and you will get a wonderful pattern.

New Year's toy "Zverushka"

For this toy, you only need flour,salt and a little water. From these ingredients, mix the salted dough to the consistency of soft plasticine. Now from this test you can sculpt all kinds of animals, birds, fish. Toys bake in the oven at a temperature of approximately 150 ° C until solidified. The resulting toys are either left just white, or painted with gouache. By the way, gouache can be added to the mixing process.